- Gear Oil
- Drain plugs?
- Servicing a sterndrive
- Impeller Installation
- Diagnose Alpha 1 Problem
- When to change oil?
- Installing a drive
- problem with gear changing
- Clanking sound when I turn the steering to left or right lim
- Changing Drive ratios implications
- Gear installation AlphaOne
- impellor question
- anode bolt
- Shift Cable Replacement - After New Drive Installation
- Lower unit
- New lower unit installed, 1 problem.
- Can I use Synthetic Gear Lube?
- New Drive Rotation
- lower unit gear backlash
- Shaft from lower to Upper half question
- Initial running in period – bearing sound
- SMOKE COMING OUT OF O/D
- Shifting problem.
- What Lube for U-Joints
- Remote Cable Adjustment
- Shift Shaft Question
- Water in gear lube.
- Warranty Period
- Drive Shower?
- www.sterndrive.cc/pdf/shift.pdf
- Replacement parts
- Aluminium alloy
- Horsepower Rating
- Alpha Shift Cable Lubrication?
- What Drive is it
- Kinked Water Hose on Alpha
- Went to replace Alpha Waterpump and found Shaft Play
- Request for information
- shaft play
- water stream coming from hole
- pre load pin
- First fluid change...
- Getting hot at idle
- Greasing U-Joints
- Tool required to install Anode?
- Break-in Time
- Which Outdrive?
- Noise when turning
- Prop Cavitation during break in period
- Alpha 1, Gen 2 outdrive problems... rebuild, or buy new one?
- Did I get the wrong ratio?
- I Lost reverse after 8 hrs. Help
- Dumb Question
- Aftermarket Hydrofoil Attachments
- Bad U joints?
- Brass shift shaft
- Drive Installation
- Mercruiser I
- Ratio?
- Twin Drive Question ?
- UPPER CASE SEAL
- SHIFTSLIDE POCKET UPPER DRIVESHAFT HOUSING
- Brass Shift shaft adjustment
- Seal
- HP rating
- Upper unit
- upper unit
- Dark Lube at draining
- shower cooler on SE106
- Water leaking into boat and water in gear oil.
- Replacement for 72 165hp mercruiser outdrive ?
- Updating 888 Merc
- SE 106 Install, lube and maintenance
- sterndrive question
- O/D trailering options
- SE 106
- Gear oil
- parts replacement
- Drive Shower
- gimal bearings and impeller replacement
- getting these drives to work
- ratio on older drive
- Pennzoil Sterndrive Lube Question
- can't quite get it
- Replace old MerCruiser 215H's
- Water pumps
- Noise
- welch plug popped out
- omc cobra - troubleshooting coolant system
- Gear problems
- good product
- se106 Sterndrives
- Shifting into Reverse
- Can't get sterndrive in the last inch
- Unsure about MR drive
- Re replacement for 106
- sterndrive for Merccruiser
- oil filter
- Identifying my outdrive??
- Gen I or Gen II ???
- Noise and shifting
- sterndrive lubticant
- Loud whinning on new SE 106
- convert to counter rotation
- prop hits trim tab
- complete out drive
- 1969 merc sterndrive replacement
- stripped gears in upper unit
- GEAR RATIO
- gear ratio
- SE106 Prop size and Thumping noise question
- Gear Whine in Neutral
- adjustment or bad dog clutch
- se106 installed
- Installation Questions
- u joint problems
- Oil Level
- gear question
- input shaft or alingment tool
- Slipping Mercruiser over 1500 RPM??
- Which gear ratio is best for my boat
- Water pump volume
- replace lower unit vs. whole drive?
- overheating
- Lining up the shift shafts
- Comparing new to old
- 106 Drive
- what drive ?
- Another Gear Ratio Question
- Wear Pads
- Drive problem
- 1972 Mercruiser
- KNOCKING NOISE
- overheating
- will not shift into reverse
- Ford 351 Mercruiser w/ Alpha One Drive - Gear Ratio
- shifting problem
- Break-in new SE 106
- New Drive Ratio
- 350 ci
- gear ratio question
- Separating upper from lower
- Shifting gets worse after ten to twenty minutes running
- 91 Yamaha (YEMS) Shift Problem
- Gen 2 style remote oil reservoir and alarm
- UPPER SHIFT BUSHING
- no reverse
- No reverse after adjusting cutout switch
- water in drive oil
- prop size
- fitments
- Replacing older drive
- prop dia
- Old model not sure
- short yoke installation.
- Complete drive and RPM change
- GearRatio
- idle speed overheat
- low speed overheating
- high speed overheating
- 1970 skipjack ?????
- Winterization
- What Prop?
- Engine alignment tool
- bellows replacement
- 1973 mercruiser 888?
- gear ratio
- Corrosion Resistance
- Outdrive Movement
- Gear oil, oil filter, power tilt & trim fluid
- shift lever degrees
- Seperating Upper From Lower Alpha 1
- Which ratio?
- Another Ratio Question
- drive overheating and will not shift
- Gear ratio
- Older Mercruiser 120 Compatible?
- Gear oil
- painting
- Install Kit Gasket
- Shift shaft bushing
- Complete Install Kit
- pre-alpha transom seal kit
- Lower Seals
- Strange Noise in Neutral on new SE106
- New Member/possible customer
- Thrust washer
- Replacement for Bayliner Boats
- SEI gear change
- power steering fluid leaking out of cap
- overheating at idle
- Excessive Slap
- Terry
- Continuity Kit
- noise
- Gimbal Bearing Failure Insurance
- Loud everything
- Whine/Hard Crank
- Changing out the yoke
- possible bad bearing
- CR or NOT
- New heating find
- Lower Unit Install - Water Pump Drive Shaft Froze
- Wrong Drive
- Torque
- 106 going good
- Anode Kit for SE 106
- New SE 106
- Shifting
- shift lever
- ONe problem with my new alpha drive
- so many concerns?
- Great Product, But...
- U joint Failure
- Paint Chipping Off upper and lower unit
- reverse problems
- pre alpha hydraulic reverse lock out
- Sea Ray 250da, ratio problems!!!
- brass shift lever
- sick of this problem totally burned out,sad!
- break in - can't break 2000 rpm
- Loss of Forward Gear
- 1300 rpm loss?
- 1972 searay srv190 with 888
- Synthetic Lube in SE106?
- New to Board/what else do I need....
- Overheated
- what is your return policy???
- new complete se 106
- No foreward / reverse
- slight growling
- Universal joints
- SE116 makes a load clicking noise full L or R
- Noise in unit
- 106 just installed shifting problems
- Need help
- Damage assessment and Drive ratio and type
- Drive ratio
- Received my new 106 lower unit
- Hydrofoil
- 40 Hrs And Sounds Like An Outboard
- Stern drive slipping
- engine coupler
- Determining Warranty eligibility + clarification on drive noise
- 1987 Alpha SS Upper Gearset
- Shifting Problem
- Help What Do I Need
- Low RPM Overheating
- se106
- New SE106 Installed. Slight issue.